Your cart is empty. Go to Checkout Software and Audio ART CLEANBOX II HUM ELIMINATOR Our Price: AU$79.00 ART Pro Audio: ARTcessories™CleanBOX II - Hum EliminatorRRP $99.99 our price $79 “Hum” in an audio system is often caused by loop effects which act like antennas. These loops can easily pick up a 50 Hz (or higher harmonics) hum transmitted by electrical wiring. Typically, these loops are connected via grounds, more commonly called “ground loops”. The safest way to eliminate unwanted noise is with the CleanBOX II. Some examples of Ground Loops: The power ground of a synthesizer, connected to the signal ground of the synth, into a mixer’s ground, then into a mixer’s power ground. The signal ground of a send effect (reverb, delay) into a mixer, and the connecting power grounds of the mixer and the unit. The power ground of a guitar amplifier, connected to a signal processor which has a second guitar amplifier on the other channel, and then the second guitar amp’s power ground. The CleanBOX II easily removes ground loops without any signal degradation. ARTcessories™ OveriewARTcessories are taking the audio world by storm and quickly becoming a popular brand with musicians, DJs and studio engineers everywhere around the World. Split, combine, mix, power... you name it. On stage, in the studio, in your living room, they’re easy to use and are built to last. For those times when you need a little box to fix a big need or to make more out of a smaller project, ARTcessories has you covered. You’ll discover a robust line of useful tools which include a complete range of direct boxes, headphone amps, small mixers, mic cable combiner/splitters and much more. ARTcessories are designed to deliver affordable solutions for a multitude of audio needs for any size project. ART DJ PRE II Our Price: AU$89.00 ART Pro Audio: ARTcessories™DJPRE II - Phono PreamplifierRRP $109.99 - our price $89 The DJ PRE II (formerly named the “Phono MicroPRE”) acts as an interface between your turntable and your audio recording / playback system. The analog input capacitance can be switched between 100pF and 200pF to optimize your phono cartridge response. A switchable low cut filter removes turntable rumble while leaving the audio pristine. The front gain trim control and signal/clip LED allow you to optimize the preamp’s gain for a wide range of input sources. The built-in low noise phono preamp circuitry is highly accurate and precisely conforms to the RIAA standard. The line output jacks are low impedance and can be used with any sound card. Housed in an all aluminum black anodized case, the DJ PRE II can be powered by a wide variety of external supplies. If you need to amplify and EQ your vinyl records to interface with your audio workstation, sound card, home stereo system or main monitor system, the DJ PRE II gives you flawless audio reproduction in a rugged and reliable package. ART MACROMIX 4 CHANNEL PERSONAL MIXER Our Price: AU$89.00 ART Pro Audio: ARTcessories™MacroMIX - Four Channel Personal MixerRRP $119.99 - our price $89 Problem: You need to mix a CD and a VCR’s audio output with a synthesizer and the line output of a bass amp and send it all to a PC or cassette deck. Solution: Connect the MacroMIX between your audio sources and the PC or cassette deck. Levels can be mixed and a headphone jack lets you monitor the mix. Mix it up however you like! Specifications Signal To Noise Ratio>90dB Maximum Gain+40dB Input Impedance10K ohms unbalanced (all inputs) IMD (SMPTE)<0.008% Power Requirements12V DC (Adapter included) Total Harmonic Distortion<0.008% Dimensions5.625x3.75x1.75 inches (143mm x 92mm x 45mm) Weight1.6 lbs (725g) ART PROMIX MICROPHONE MIXER Our Price: AU$159.00 ART Pro Audio: ARTcessories™ProMIX - Three Channel Microphone Mono MixerRRP $199.99 - our price $159 Problem: You need to add 3 mics to a mixer, which only has one available channel. Solution: Insert a ProMIX between the mics and the mixer. Each mic channel on the ProMIX has both phantom power and low-frequency cut selectable via DIP switches plus a level control. The balanced XLR line output can be connected to a mic input on the mixer and headphones or a powered monitor can be connected to the Phone/Aux output. And if AC power is not available, the ProMIX runs on batteries as well. Specifications Maximum Gain+60dB Input Impedance600 ohms Maximum Input Level-14dB Maximum Output Level+14dB Output Impedance600 ohms Total Harmonic Distortion0.02% Low Cut-3dB @ 100Hz Clip Headroom3dB Output Phantom Power12V DC Power12V DC (adapter) / 2x 9V (batteries) Dimensions5.625x3.75x1.75 inches (143mm x 92mm x 45mm) Weight1.5lb (680g) ART TUBE MP PREAMP Our Price: AU$89.00 ART Pro Audio: Tube Mic PreampsTube MP - The Original RRP $109 - our price $89 The Tube MP is the world’s most popular external tube microphone preamp. Whether you’re working with a digital, computer or analog recording system, the Tube MP’s TEC award nominated design will allow you to obtain professional recording studio results at a fraction of the cost of comparable equipment. The hybrid design of the Tube MP allows it to add warmth and fatness to a signal while maintaining exceptionally low-noise and high quality. While its primary application is to be used with a microphone, the Tube MP is an exceptional direct box - impedance matching, amplifying and improving the sound of any instrument plugged into it. The usage of external mic/line preamps has become increasingly popular over the past several years. The Tube MP offers superior performance and sound quality to the “on-board” preamps found in today’s low-cost mixers and multi-trackers. It’s sound has been consistently favored over other products costing upwards to ten-times its price. Professional quality sound combined with professional features like: a hand-selected 12AX7a tube, phantom power and phase reverse are what have made the Tube MP a staple in thousands of studios worldwide. For a minimal investment, a Tube MP can provide the single largest improvement to the sound of your studio.Features Provides Superior Preamplification for: Microphones, Instruments and Line Level Sources Hand Selected 12AX7a Provides 70dB of Gain Smooth, Warm and Fat Sound Quality Variable Input and Output Gain Controls Excellent as a Tube DI XLR and 1/4" Inputs and Outputs +48 volts Phantom Power Phase Reversal Switch Superior Sonic Performance to On-Board Preamps TEC-Award Nominated Design Portable, All Steel Construction 1 Year Warranty ART TUBE MPV3 PREAMP Our Price: AU$129.00 ART Pro Audio: Tube Mic PreampsTube MP – Studio V3™RRP $169 - our price $129 The Tube MP Studio V3 delivers warmth and fatness to any audio source while maintaining an exceptionally low-noise signal path. While its primary function is as a microphone preamp with +48V phantom power, variable gain and phase reverse switching, the Tube MP is also an exceptionally versatile tube driven direct box for any instrument source. The Tube MP Studio V3 uses ART’s proven V3™ (Variable Valve Voicing) Technology to instantly contour the tone to any source. V3™ presets were created and fine-tuned by some of the industry's top studio and live-sound engineers and allow instant access to a multitude of preamp settings designed for guitars (electric and acoustic), keyboards, bass guitars, drums, vocals and more. Additionally, the Tube MP Studio V3 employs OPL™ (Output Protection Limiting) technology to protect the next component in your signal path from clipping and overloads. The Tube MP Studio V3 offers exceptional sound quality and superior performance to that typically found in “on-board” preamps found in today’s low-cost mixers, multi-track recorders and audio cards making it an ideal tone-shaping tool for any application. Features Provides Superior Preamplification for: Microphones, Instruments and Line Level Sources V3™ - Variable Valve Voicing OPL™ - Output Protection Limiting Hand Selected 12AX7A Provides 70dB of Gain Smooth, Warm and Fat Sound Quality Variable Input and Output Gain Controls Excellent as a Tube DI XLR and 1/4" Inputs and Outputs +48 Volts of Phantom Power Phase Reversal Switch Portable, All Steel Construction ART USB DUAL PRE Our Price: AU$155.00 USB Dual Pre - Two Channel preamp with USBRRP $219.99 - our price $155 The USB Dual Pre is a full-featured high quality dual portable preamplifier and computer interface packed into a compact rugged case. It is designed to work over a wide variety of applications from remote field recording to desktop/studio tracking. Each of the two low noise input channels has up to 48 dB of clean gain with signal present and clip LED indicators. Inputs can be either XLR balanced or 1/4-inch TRS. Each of the 1/4-inch TRS outputs is buffered low impedance balanced. The USB Dual Pre can be externally powered from the mains via a supplied 12 Volt DC adapter, or from an internal 9 Volt battery, or from the USB bus itself, or any combination of these power sources. When running off of the battery alone, you should get in excess of 50 hours of operation when phantom power is off. Battery life drops to around 20 hours (depending on microphone) when phantom powering from the battery alone (still enough time to get through a session). The built-in low noise +48 Volt phantom power supply allows you to power up to 2 microphones as well as the preamplifier when running from any power sources including the USB bus. For monitoring, an 1/8-inch TRS mini headphone jack with level and monitor mix controls on the rear allow for latency free local monitoring of the inputs while recording as well as playback monitoring of the USB bus. The monitor mix is also routed to the 1/4-inch TRS balanced outputs. This lets you use the 1/4-inch outputs as either preamplifier outputs or as the monitor feed to your powered monitors. The USB interface is fully compliant with the USB 1.1 specification and uses USB adaptive mode for playback and USB asynchronous mode for record. It will work with the USB audio device drivers built into Windows 98SE/ME/2000/XP/Vista and Apple OS9.1/OSX computers with native USB support. No special drivers are needed. The compact black anodized all aluminum case with rubber sides make for a rugged design. The USB Dual Pre will provide years of trouble free service and its high quality audio channels and versatile powering options make the USB Dual Pre the obvious choice in a wide variety of applications from Podcasting/Broadcasting to Tracking and Monitoring. With the USB Dual Pre, your laptop, and a pair of quality condenser microphones you can do some serious remote recording.Features USB Connectivity to Desktop and Laptop Computers Low Noise Fully Balanced XLR and 1/4-inch TRS Combi Inputs Up to 48 dB of Clean Gain Built-in Low Noise Phantom Power Supply Latency Free Monitoring Mix and Level Controls Independent Channel Gain Controls 1/4-inch TRS Balanced Monitor and 1/8-inch Headphone Monitor Outputs Compact, Stackable all Aluminum Chassis Flexible 3-way Power from USB, External Supply, or 9 Volt Battery Belkin Tune Studio for iPod Our Price: AU$399.00 The Belkin Tune Studio for iPod is a 4-channel audio mixer that lets you create high quality (16bit, 44kHz) digital recordings directly into your iPod. Compatible with: iPod classic: 80GB, 60GB 2nd gen iPod: 2GB, 4GB, 8GB 3rd gen iPod nano: 4GB, 8GB 5th gen iPod (video): 30GB, 60GB, 80GB FEATURES Records to 16bit, 44kHz quality Stream audio by USB to PC or Mac Each channel has: 3-EQ, pan, level controls Phantom-power enabled XLR inputs provide up to 60 dB of microphone gain High-quality stereo compressor keeps audio levels within recording limits of your iPod Features one-knob compression control RCA, XLR, 1/4 inch input friendly
“Hum” in an audio system is often caused by loop effects which act like antennas. These loops can easily pick up a 50 Hz (or higher harmonics) hum transmitted by electrical wiring. Typically, these loops are connected via grounds, more commonly called “ground loops”. The safest way to eliminate unwanted noise is with the CleanBOX II. Some examples of Ground Loops:
ARTcessories are taking the audio world by storm and quickly becoming a popular brand with musicians, DJs and studio engineers everywhere around the World. Split, combine, mix, power... you name it. On stage, in the studio, in your living room, they’re easy to use and are built to last. For those times when you need a little box to fix a big need or to make more out of a smaller project, ARTcessories has you covered. You’ll discover a robust line of useful tools which include a complete range of direct boxes, headphone amps, small mixers, mic cable combiner/splitters and much more. ARTcessories are designed to deliver affordable solutions for a multitude of audio needs for any size project.
The DJ PRE II (formerly named the “Phono MicroPRE”) acts as an interface between your turntable and your audio recording / playback system. The analog input capacitance can be switched between 100pF and 200pF to optimize your phono cartridge response. A switchable low cut filter removes turntable rumble while leaving the audio pristine. The front gain trim control and signal/clip LED allow you to optimize the preamp’s gain for a wide range of input sources. The built-in low noise phono preamp circuitry is highly accurate and precisely conforms to the RIAA standard. The line output jacks are low impedance and can be used with any sound card.
Housed in an all aluminum black anodized case, the DJ PRE II can be powered by a wide variety of external supplies. If you need to amplify and EQ your vinyl records to interface with your audio workstation, sound card, home stereo system or main monitor system, the DJ PRE II gives you flawless audio reproduction in a rugged and reliable package.
Problem: You need to mix a CD and a VCR’s audio output with a synthesizer and the line output of a bass amp and send it all to a PC or cassette deck.
Solution: Connect the MacroMIX between your audio sources and the PC or cassette deck. Levels can be mixed and a headphone jack lets you monitor the mix. Mix it up however you like!
Problem: You need to add 3 mics to a mixer, which only has one available channel.
Solution: Insert a ProMIX between the mics and the mixer. Each mic channel on the ProMIX has both phantom power and low-frequency cut selectable via DIP switches plus a level control. The balanced XLR line output can be connected to a mic input on the mixer and headphones or a powered monitor can be connected to the Phone/Aux output. And if AC power is not available, the ProMIX runs on batteries as well.
The Tube MP is the world’s most popular external tube microphone preamp. Whether you’re working with a digital, computer or analog recording system, the Tube MP’s TEC award nominated design will allow you to obtain professional recording studio results at a fraction of the cost of comparable equipment. The hybrid design of the Tube MP allows it to add warmth and fatness to a signal while maintaining exceptionally low-noise and high quality. While its primary application is to be used with a microphone, the Tube MP is an exceptional direct box - impedance matching, amplifying and improving the sound of any instrument plugged into it.
The usage of external mic/line preamps has become increasingly popular over the past several years. The Tube MP offers superior performance and sound quality to the “on-board” preamps found in today’s low-cost mixers and multi-trackers. It’s sound has been consistently favored over other products costing upwards to ten-times its price. Professional quality sound combined with professional features like: a hand-selected 12AX7a tube, phantom power and phase reverse are what have made the Tube MP a staple in thousands of studios worldwide. For a minimal investment, a Tube MP can provide the single largest improvement to the sound of your studio.
The Tube MP Studio V3 delivers warmth and fatness to any audio source while maintaining an exceptionally low-noise signal path. While its primary function is as a microphone preamp with +48V phantom power, variable gain and phase reverse switching, the Tube MP is also an exceptionally versatile tube driven direct box for any instrument source.
The Tube MP Studio V3 uses ART’s proven V3™ (Variable Valve Voicing) Technology to instantly contour the tone to any source. V3™ presets were created and fine-tuned by some of the industry's top studio and live-sound engineers and allow instant access to a multitude of preamp settings designed for guitars (electric and acoustic), keyboards, bass guitars, drums, vocals and more. Additionally, the Tube MP Studio V3 employs OPL™ (Output Protection Limiting) technology to protect the next component in your signal path from clipping and overloads.
The Tube MP Studio V3 offers exceptional sound quality and superior performance to that typically found in “on-board” preamps found in today’s low-cost mixers, multi-track recorders and audio cards making it an ideal tone-shaping tool for any application.
The USB Dual Pre is a full-featured high quality dual portable preamplifier and computer interface packed into a compact rugged case. It is designed to work over a wide variety of applications from remote field recording to desktop/studio tracking. Each of the two low noise input channels has up to 48 dB of clean gain with signal present and clip LED indicators. Inputs can be either XLR balanced or 1/4-inch TRS. Each of the 1/4-inch TRS outputs is buffered low impedance balanced.
The USB Dual Pre can be externally powered from the mains via a supplied 12 Volt DC adapter, or from an internal 9 Volt battery, or from the USB bus itself, or any combination of these power sources. When running off of the battery alone, you should get in excess of 50 hours of operation when phantom power is off. Battery life drops to around 20 hours (depending on microphone) when phantom powering from the battery alone (still enough time to get through a session).
The built-in low noise +48 Volt phantom power supply allows you to power up to 2 microphones as well as the preamplifier when running from any power sources including the USB bus.
For monitoring, an 1/8-inch TRS mini headphone jack with level and monitor mix controls on the rear allow for latency free local monitoring of the inputs while recording as well as playback monitoring of the USB bus. The monitor mix is also routed to the 1/4-inch TRS balanced outputs. This lets you use the 1/4-inch outputs as either preamplifier outputs or as the monitor feed to your powered monitors.
The USB interface is fully compliant with the USB 1.1 specification and uses USB adaptive mode for playback and USB asynchronous mode for record. It will work with the USB audio device drivers built into Windows 98SE/ME/2000/XP/Vista and Apple OS9.1/OSX computers with native USB support. No special drivers are needed.
The compact black anodized all aluminum case with rubber sides make for a rugged design. The USB Dual Pre will provide years of trouble free service and its high quality audio channels and versatile powering options make the USB Dual Pre the obvious choice in a wide variety of applications from Podcasting/Broadcasting to Tracking and Monitoring.
With the USB Dual Pre, your laptop, and a pair of quality condenser microphones you can do some serious remote recording.
Login Create New Account
Your cart is empty.
